Operation specifications and precautions of Taber abrasion resistance tester
Taber abrasion resistance tester is suitable for leather, cloth, paper, paint, plywood, leather, floor tile, glass, natural plastic, etc.
The test method is that the rotating sample bears against a pair of grinding wheels, and the specified load is applied. When the sample rotates, the grinding wheels are driven to wear the sample. The wear loss weight is the weight difference before and after the test. So what do you know about the operation specifications and precautions of Taber wear testing machine? Let's take a look at it with Qinsun Instruments Co., LTD.
Operation specification of Taber abrasion resistance tester:
connect the appropriate power supply 220V or 110V as indicated
Turn the governor switch to the lowest level to avoid the abnormal situation of the machine caused by too fast speed.
Turn on the power supply, try the machine first, and turn off the power supply if there is no abnormality.
Press the reset key to reset the counter to zero. According to the requirements, set the number of times to be tested, and the maximum counter can be set to 9999999 times. Press RST key on the counter to reset the counter, and press > key for five seconds to enter the test times setting. Eight digits on the counter respectively represent one digit to ten million digits from the bottom right to the top left. If 280,360 times are set, press > key to adjust the runout value to the third digit on the top left, press ∧ key to set the value to 2, then press > key to adjust the runout value to the fourth digit on the top left, and press ∧ key to set the value to 8. Press > again to adjust the runout value to the third number in the lower right, press ∧ to set the value to 3, then press > to adjust the runout value to the second number in the lower right, press ∧ to set the value to 6, and all other positions are set to 0. Set the required number of tests according to the test requirements.
Press the start button, and the whole machine will enter the test state.
Adjust the governor to adjust the speed to the required test speed.
Turn on the power switch of the vacuum cleaner to start working.
After the number of times set by the counter is tested, the machine will automatically stop in standby state.
turn off the power supply, remove the sample and clean the machine.
Maintenance of Taber abrasion resistance tester:
the instrument must be placed on a stable ground before use.
It is not allowed to handle the machine during use;
Choose the corresponding power supply voltage, do not be too high to avoid burning out the device;
When the instrument is abnormal, please contact our company for timely treatment;
The machine must have a good ventilation environment when working.
For each component of key machinery, please add lubricating oil to the mechanical part in time due to the heavy operating load;
After each test, clean the machine and keep it clean;
The control box shall be wiped with a dry cloth, but not with a wet cloth.
Precautions for operation of Taber abrasion resistance tester:
It shall be operated and used by professionals, and shall be cleaned and maintained regularly.
When installing grinding wheels, those marked with RIGHT WHEEL are installed on the right side, while those marked with LEFT WHEEL are installed on the left side, with the labeled side facing outward (i.e., the left side faces right and the right side faces left). When the grinding wheels wear out to the periphery of the volume label, they should be replaced immediately.3. When no test piece is placed on the test plate, do not put down the test lever arm, turn on the switch and let it idle, so as not to hurt the grinding wheel and parts.
The test lever arm and dust suction arm should be put down lightly, and the test surface should not be hit directly, so as to prolong the service life of the grinding wheel.
When balancing weights, both sides must have the same weight to ensure the accuracy of the test value.
During the test, the vacuum cleaner must be turned on to avoid dust adhering to the grinding wheel.
A little lubricating oil shall be added at any time to lubricate the test rod arm and the test disc spindle.
The above is the operation specification and precautions of Taber abrasion resistance tester shared by Qinsun Instruments Co., LTD. I hope to help everyone, thank you
